Baumatic PI645 Uživatelský manuál

1PI645 60cm Front touch control induction zone hob

Electrical details Rated Voltage: 230 Vac 50 Hz Supply Connection: 32 A (double pole switched fused outlet with 3mm contact gap) Max Rated Inputs

Control panel layout 1) Safety lock button 2) Minus button (x 4) 3) Cooking zone indicator (x 4) 4) Plus button (x 4) 5) Timer minus button 6) Timer

Touch controls o All operations are performed by means of the touch controls that can be found on the control panel. o Each touch control has a v

Switching a zone off gradually o Press the minus button (2) of the zone that you wish to switch off, until the number in the cooking zone indicator

Residual heat indicator o After a zone is switched off, the corresponding cooking zone indicator (3) will show the letter “H”. This means that the t

Cookware that is suitable for an induction hob The table below shows cookware that is normally suitable for use on an induction zone hob:- Cookware

o IMPORTANT: If the appliance is switched off whilst the safety lock feature is activated, then it will still be activated the next time that you swi

17o The booster time is limited to 5 minutes and will switch off n is removed from the zone when the booster is switched on, then the boosting funct

18 minus (5) and timer plus (7) buttons, to set the e. o The countdown time will appear on the timer display (6). o When the countdown time that

19rst few times the hob top is used, it may give off an acrid, burning smell. This smell will disappear completely with repeated o The hob surface i

User Manual for your Baumatic PI645 60 cm Front touch control induction zone hob NOTE: This User Instruction Manual contains important informat

20Cleaning and maintenance Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your re co

21nce will be provided with a hob scraper. The following uidelines should also be followed when using the ceramic hob craper:- . o Residues should

22id a rature rise of 85°C above the ambient temperature of the room it is located in, during ng on size) or 600 mm worktop that is between 5 mm and

Installing above a built under oven 23MPORTANT: If you are building this hob above an oven, the There must be a gap of at least 50 mm between the

Installing the appliance 24 Cut a hole in the worktop that corresponds with the drawing o Apply the sealing strip provided around the edge of t

25 the : There are ventilation holes around the outside of the hob. re p, when you put the hob into position (see drawing opposite). o Car

26Electrical che I.E.E. Regulations and in compliance with Baumatic’s instructions. efore connecting the appliance, make sure that the supply voltage

27Connecting the mains supply cable o derside of the hob and the terminals are accessible by removing the terminal block o 1 and 2 are the live con

28on must be tightened down firmly. of the zones work, you should recheck that the terminal screws are all o T: The appliance must NOT be connect

29My appliance isn’t working correctly Error codes Error code ble causes Possi Solution F0/F1/F2 Fan failure Contact the Baumatic Service Depart

3Contents Environmental note 4 Important safety information 5 – 8 Specifications 9 - 11 Electrical details 10 Ceramic hob

30* The cooking zone has only been turned on for a short period of IMPORTANT: If the cooking zone does appear to be hotter than should call the Ba

31 be operating correctly, then you should disconnect it from your mains supply and then contact DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. fa

Czech Republic United KingdomBaumatic Ltd., 32 Baumatic Buildings, 6 Bennet Road, Reading, BerkshireRG2 0QX United Kingdom Sales Telephon

33

34

35

36

Environmental note 4 o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. all packaging mat

5Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before at

6hild Safety d e at any time. During and after use, all surfaces will be hot. se ensure that they are kept under close supervision at all times. ld o

o IMPORTANT: This ceramic induction hob fully complies with current legislation regarding electro-magnetic interference and is designed not to interf

8Declaration of conformity This appliance complies with the following European Directives: -73/23/EEC dated 19/02/1973 Low Voltage Directive. -89/3

Specifications Product dimensions: Aperture dimensions: Height: 520 mm Height: 490 mm Width: 590 mm Width: 560 mm Depth: 52 mm Product