Baumatic cooker Uživatelský manuál

1BU676GL-EU 60 cm Cooker hood BU976GL-EU 90 cm Cooker hood

Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o Y

11Setting the time of day o After the appliance is connected to your mains supply, press the ON/OFF button to switch the hood on, the LED display b

o To switch the fan off, press the ON/OFF button. o When you next switch on the cooker hood using the ON/OFF button, it will remember the operating

Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, S

Maintenance Removing and cleaning the grease filter o Lift up the cover that sits over the grease filter (as shown in the line drawing above).

o Close the cover that sits over the grease filter. o IMPORTANT: Let the grease filter dry thoroughly before refitting it in the cooker hood. Chan

Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters. This will hel

Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated o

o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box,

o Do not tile, grout or silicone this appliance to the wall. This appliance is designed to be surface mounted only. Installing your cooker hood IMP

User Manual for your Baumatic BU676GL-EU 60 cm Cooker hood in stainless steel and glass BU976GL-EU 90 cm Cooker hood in stainless steel and glass

2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Usi

6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the rele

Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (pleas

10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the

12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and

Completing the installation If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitting

Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please

IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Cus

Czech Republic Baumatic CR spol s.r.o. Průmyslová zóna Sever 696 460 11 Liberec 11 United Kingdom Czech Republic Baumatic Ltd., Baumatic Building

29

3Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood 8 – 9 BU676GL-EU

30

31

32

ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useles

IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before att

o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN

o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed

Specifications of your cooker hood BU676GL-EU PRODUCT DIMENSIONS: Height: 540 mm Width: 600 mm Depth: 327 mm Your stainless stee

BU976GL-EU PRODUCT DIMENSIONS: Height: 540 mm Width: 900 mm Depth: 327 mm Your stainless steel cooker hood is fitted with: o Hi